Roof sheathing cleaning
Growth on the underside of the roof deck is removed by blasting or sanding, followed by HEPA vacuuming of the attic.
Attic mold almost never comes from a single leak. Call Breffni Remediation and we'll connect you with an independent attic mold pro in Angwin who removes the growth and fixes the airflow problem underneath it.
Most attic growth comes down to three issues: exhaust fans venting into the attic, blocked soffit vents, and air leaks from the house below. Cleaning without fixing them doesn't last.
Real people pick up 24/7.

Attic jobs fail when they stop at cleaning. These are the standards we look for in the contractors we refer.

The quote separates sheathing cleaning, insulation work, and ventilation corrections, so you know what each fix costs before anyone climbs the ladder.
Dry ice and soda blasting lift growth off roof decking without soaking the wood, and HEPA vacuums and air scrubbers handle the dust and spores that come loose.
Need it done before closing or before new shingles go on? Tell the dispatcher and we'll prioritize your call.
Attic work means walking joists, working near wiring, and sometimes cutting new vents. The pros we route you to carry their own insurance and required licensing.
Here's what independent contractors in our network handle most often in attics.
Growth on the underside of the roof deck is removed by blasting or sanding, followed by HEPA vacuuming of the attic.
Exhaust fans that dump humid air into the attic are one of the most common causes. Ducts are extended and terminated through a roof or wall cap so moisture leaves the house.
Insulation pushed against the eaves can block soffit intake. Baffles restore the air channel, and ridge or roof vents are checked so air flows from low to high.
Removing damaged insulation and sealing the gaps where house air escapes keeps the attic colder and drier.
Once the decking is clean, some contractors apply an antimicrobial or a fungicidal encapsulant coating. It doesn't replace cleaning or ventilation fixes, but it adds a layer of protection.

Four steps, with photos from up top.
Share the inspection notes if you have them so the contractor knows what to look for.
The pro checks the sheathing, ventilation, insulation depth, exhaust duct terminations, and roof penetrations, taking photos along the way.
The quote shows what needs cleaning and what needs fixing so it stays clean.
Decking is cleaned, exhaust routed outside, vents restored, and the job finishes with before-and-after photos you can share with a buyer or insurer.

One free call gets a local attic mold pro to take a look.
Speak to Dispatch: +1-844-326-4757
A few recent attic jobs.

The north slope of our roof deck was covered in dark stains. The contractor found both bathroom fans venting straight into the attic. They dry ice blasted the decking and ran the ducts out through roof caps.
Every winter we'd get water spots on the bedroom ceiling. Frost was building on the nail tips and melting. They cleared the soffits, installed baffles, and sealed around the can lights. No spots this year.
We were about to replace the roof anyway, so the contractor cleaned the sheathing first and coordinated with the roofer on adding a ridge vent. Good timing saved us a second trip.
Photos of the cleaned attic saved our closing. The buyer's agent had questions and the report answered every one of them.
Usually warm, humid air from the house condensing on cold roof sheathing, made worse by exhaust fans venting into the attic, blocked soffit vents, or poor air sealing. Roof leaks are another cause.
It can still damage the roof deck and insulation, and it often becomes an issue when you sell.
Only if the wood is rotted or delaminating. Cleaning handles most attic mold.
It's a method that fires dry ice pellets at the surface to knock off growth. The dry ice turns into gas, leaving no water or grit behind, which suits attic sheathing well.
No. Bath and kitchen exhaust should be ducted all the way outside through a roof or wall cap. Venting into the attic is one of the most common causes of attic mold.
Most attic jobs take one to three days, depending on attic size, access, the cleaning method, and how many ventilation corrections are needed.
Ranch homes, two-stories, and older houses with low-slope roofs across Angwin all use the same 24/7 line.
Common Angwin service zip codes include 94508.
Nearby cities we also serve sit in the list below.
Call +1-844-326-4757 to Confirm